Can I Remove A Weld-On Trailer Coupler and Replace it With A Bolt-On Coupler?
Question:
I have 2 trailers. One with 1 7/8 coupling and the other one with a 2 inches coupling. I would like to change everything to 2 inches. The coupling on the 1 7/8 is welded. Can I just remove it and install a new 2 inches drilling the holes?
asked by: Lisandro A
Expert Reply:
Yes, you can remove your weld-on coupler and install a new bolt-on coupler that fits a 2 inch ball. There is just a few things you need to do to before and when installing.
You need to know what channel size and the weight capacity you will need for the new coupler. The most common sizes are the 2, 2-1/2 and 3 inch channels. Coupler, # CT-3001-Z , can be used if you have a 2 inch channel and a weight capacity of 3,500 lbs. If you need a coupler for a 3 inch channel, the Fulton # F343000301 would will work for this application and has a 5,000 lbs capacity.
When you go to remove the weld-on coupler you need to make sure you break the welds and do not cut into the trailer frame. Place the new coupler on the channel and use a marker to mark through the bolt holes on the frame to show where you will need to drill. You will need a drill bit that will make a 1/2 inch hole in the frame to install the coupler.
Drilling new holes in the frame will be okay because you will be reinforcing the structure by the addition of bolts. You should use bolts that go through the trailer frame. You will need two 1/2 inch diameter grade 5 bolts about 4 inches long and nuts to install the coupler to the trailer.
Products Referenced in This Question
Fulton Fas-Lok Coupler, 2" Ball, 3" Channel - 5,000 lbs
- Straight Tongue Trailer Coupler
- Standard Coupler
- 2 Inch Ball Coupler
- Bolt-On
- 5000 lbs GTW
- 3 Inch Channel
- Trigger Latch
- Fulton
more information >
Product Page this Question was Asked From
Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 2" Ball - Bolt On - 3,500 lbs
- Straight Tongue Trailer Coupler
- Standard Coupler
- 2 Inch Ball Coupler
- Bolt-On
- 3500 lbs GTW
- 2 Inch Channel
- Trigger Latch
- etrailer
more information >
Continue Researching
- Shop: Demco A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Black - 2" Ball - Bolt On - 10K
- Q&A: What Kind Of Plug Do I Need In Order To Use The DX29FR Surge Brake Actuator
- Shop: Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K
- Shop: Demco Cast Head Coupler w/ Jack Hole - eZ-Latch - 2" Ball - A-Frame - Bolt-On - 10K
- Shop: Trailer Wiring
- Video: Demco Cast Head Coupler with Jack Hole Review
- Shop: Demco A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Silver - 2" Ball - Bolt On - 10K
- Article: Trailer Tire Sizing
- Shop: Brake Controller
- Shop: Trailer Hitch
- Q&A: Replace Trailer Surge Coupler with Straight Coupler on a Trailer With Surge Brakes
- Video: Demco eZ-Latch A-Frame Trailer Coupler Review and Installation
- Video: Review of Demco A-Frame Trailer Coupler - Cast Head Coupler - DM37ZR
- Shop: Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs
- Shop: Fulton Fold-Away Coupler Hinge Kit for 2" x 3" Trailer Tongue - Bolt On - Up to 5,000 lbs
- Q&A: Picking Out Bearing Kit for Trailer with 2,000 lb Axles
- Shop: Optronics Fleet LED Trailer Tail Lights w/ Grommets - Stop,Turn,Tail - Submersible - Oval - Qty 2
- Search Results: swing away trailer tongue
- Search Results: swing away
- Search Results: trailer coupler
- Search Results: bearing buddy
- Video: Choosing the Right Trailer Wiring
- Search Results: coupler pin
- Article: Measuring a Trailer Tire
- Video: Demco A-Frame Trailer Coupler - Standard Coupler - DM14793-52 Review
- Q&A: Will a 5.30 x 12 Trailer Tire Fit the Same Rim as a 4.80 x 12 Trailer Tire
- Q&A: Recommended 4 on 4 Idler Hub for an Axle w/ L44649 Inner and Outer Bearings
- Search Results: self tapping
- Video: Review of Demco Brake Actuator - Surge Brake Actuator - DM72VR
- Video: Demco A-Frame Trailer Coupler - Standard Coupler - DM14793-81 Review